Updates and fixes

update /macros folder

Update *bltouch.cfg

Fix Z and Y pins

Fix Y direction

Update MKSRN-Sv1.3 pins

Clean obsolete comments

Flying Bear Generic Configs/board/mks-rn-s-13.cfg

@@ -120,15 +120,11 @@ aliases:
 ## Controls ####################################################################
   MT_DET1_PIN=PA4, MT_DET2_PIN=PE6, 
   PW_DET_PIN=PA2, AUTO_OFF_PIN=PB2, 
-  BEEPER_PIN=PC5, 
 ## BLTouch #####################################################################
   BLTOUCH_SENSOR_PIN=PE6,                                                       # MT_DET2
   BLTOUCH_CONTROL_PIN=PA8,                                                      # SERVO
 ## TMC2209 UART ################################################################
-  X_UART_PIN=PA1, X_TX_PIN=PA6, 
+  TMC_UART_PIN=PA1, TMC_TX_PIN=PA6, 
-  Y_UART_PIN=PA1, Y_TX_PIN=PA6, 
-  Z_UART_PIN=PA1, Z_TX_PIN=PA6, 
-  E0_UART_PIN=PA1, E0_TX_PIN=PA6, 
 
 ################################################################################
 # MCU
@@ -148,7 +144,7 @@ min_temp: 0
 max_temp: 100
 
 [filament_switch_sensor filament_sensor]
-switch_pin: MT_DET1_PIN
+switch_pin: PA4
 runout_gcode:
     BEEP P=1500
 
@@ -157,7 +153,7 @@ runout_gcode:
 ################################################################################
 
 [output_pin _BEEPER_pin]
-pin: BEEPER_PIN
+pin: PC5
 pwm: True
 value: 0
 shutdown_value: 0

Flying Bear Generic Configs/fb-ghost4s-printer.cfg

@@ -61,7 +61,7 @@ position_endstop: 0.5
 ################################################################################
 
 [extruder]
-rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html; FBG5: 7.880, FBG4S: 7.600
+rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 pressure_advance: 0.000                                                         # CAUTION! Calibrate using https://www.klipper3d.org/Pressure_Advance.html
 control: pid                                                                    # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands

Flying Bear Generic Configs/fb-ghost5-printer.cfg

@@ -65,7 +65,7 @@ position_endstop: 0.5
 ################################################################################
 
 [extruder]
-rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html; FBG5: 7.880, FBG4S: 7.600
+rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 pressure_advance: 0.000                                                         # CAUTION! Calibrate using https://www.klipper3d.org/Pressure_Advance.html
 control: pid                                                                    # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands

Flying Bear Generic Configs/fb-reborn-printer.cfg

@@ -68,7 +68,7 @@ position_endstop: 0.5
 ################################################################################
 
 [extruder]
-rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html; FBG5: 7.880, FBG4S: 7.600
+rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 pressure_advance: 0.000                                                         # CAUTION! Calibrate using https://www.klipper3d.org/Pressure_Advance.html
 control: pid                                                                    # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands

Flying Bear Generic Configs/macros/filament_management.cfg

@@ -0,0 +1,111 @@
+################################################################################
+# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
+# Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
+# G-code Macros by ODUCCEU
+################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
+
+# Filament Change ##############################################################
+
+[gcode_macro FILAMENT_CHANGE]
+# Unloads filament, waites 5 minutes for manual filament switch and loads again
+gcode:
+    SAVE_GCODE_STATE NAME=FILAMENT_CHANGE_STATE
+    {% set timer = params.T|default(300)|float %}
+    {% set unload = params.U|default(100)|float %}
+    {% set load = params.L|default(100)|float %}
+    {% if printer.pause_resume.is_paused %}
+        M118 Already paused
+    {% else %}
+        {% if printer.toolhead.homed_axes != "xyz" %}
+            M118 Homing
+            G28                                                                 # home if not homed
+        {% else %}
+            M118 Pausing print
+            PAUSE
+        {% endif %}
+    {% endif %}
+    M118 Changing filament...
+    SET_IDLE_TIMEOUT TIMEOUT=7200
+    FILAMENT_UNLOAD U={unload}
+    COUNTDOWN TIME={timer} MSG="Change filament! Time left: "
+    FILAMENT_LOAD L={load}
+    RESTORE_GCODE_STATE NAME=FILAMENT_CHANGE_STATE
+
+[gcode_macro FILAMENT_LOAD]
+gcode:
+    {% set load = params.L|default(100)|float * 0.5 %}
+    {% set extruder_temp = params.T|default(220)|float %}
+    SAVE_GCODE_STATE NAME=FILAMENT_LOAD_STATE
+    LOW_TEMP_CHECK T={extruder_temp}
+    M118 Loading filament...
+    M83                                                                         # relative extrusion
+    G0 E{load} F600                                                             # load the filament into the hotend area
+    G4 P1000                                                                    # wait 1 second
+    G1 E50 F100                                                                 # purge
+    M400                                                                        # wait until all moves are completed
+    M118 Filament loaded!
+    BEEP
+    RESTORE_GCODE_STATE NAME=FILAMENT_LOAD_STATE
+
+[gcode_macro FILAMENT_UNLOAD]
+gcode:
+    {% set unload = params.U|default(100)|float %}
+    {% set extruder_temp = params.T|default(220)|float %}
+    SAVE_GCODE_STATE NAME=FILAMENT_UNLOAD_STATE
+    LOW_TEMP_CHECK T={extruder_temp}
+    M118 Unloading filament
+    M83                                                                         # relative extrusion
+    G0 E-5 F3600                                                                # extract filament to the coldend zone 
+    G4 P3000                                                                    # wait for 3 seconds
+    G0 E5 F3600                                                                 # push back the filament to smash any stringing 
+    G0 E-15 F3600                                                               # extract back fast to the coldend zone 
+    G0 E-{unload} F300                                                          # extract a lot
+    M400                                                                        # wait until all moves are completed
+    M118 Filament unloaded!
+    BEEP
+    RESTORE_GCODE_STATE NAME=FILAMENT_UNLOAD_STATE
+
+[gcode_macro LOW_TEMP_CHECK]
+gcode:
+    {% set extruder_temp = params.T|default(220)|float %}
+    {% if printer.extruder.target > extruder_temp %}                            # check for a setpoint for extruder
+        {% set extruder_temp = printer.extruder.target %}
+    {% endif %}
+    {% if printer.extruder.temperature < extruder_temp %}                       # heat to the target temp
+        M118 Heating to {extruder_temp}
+        SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}
+        TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}
+    {% endif %}
+
+[gcode_macro COUNTDOWN]
+gcode: 
+    {% set timer = params.TIME|default(10)|int %}
+    {% set message = params.MSG|default("Time: ") %}
+    # countdown
+    {% if timer > 60 %}
+        {% for s in range(timer, 60, -10) %}
+            M118 {message} {s}s
+            G4 P10000                                                           # wait 10 seconds
+        {% endfor %}
+        {% set timer = 60 %}
+    {% endif %}
+    {% if timer > 10 %}
+        {% for s in range(timer, 10, -5) %}
+            M118 {message} {s}s
+            G4 P5000                                                            # wait 5 seconds
+        {% endfor %}
+        {% set timer = 10 %}
+    {% endif %}
+    {% if timer > 0 %}
+        {% for s in range(timer, 0, -1) %}
+            M118 {message} {s}s
+            G4 P1000                                                            # wait 1 second
+        {% endfor %}
+    {% endif %}
+    BEEP
+
+################################################################################

Flying Bear Generic Configs/macros/macros.cfg

@@ -3,6 +3,18 @@
 # Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
 # G-code Macros by ODUCCEU
 ################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
+
+# Documentation
+# https://www.klipper3d.org/G-Codes.html
+# https://www.klipper3d.org/Command_Templates.html
+
+################################################################################
+# Included macros
+################################################################################
 
 [include print_management.cfg]
 [include prime_line.cfg]

Flying Bear Generic Configs/macros/macros_marlin.cfg

@@ -0,0 +1,123 @@
+################################################################################
+# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
+# Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
+# G-code Macros by ODUCCEU
+################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
+
+# Marlin Compatibility #########################################################
+
+[gcode_macro G27]
+gcode:
+    PARK
+
+[gcode_macro M125]
+gcode:
+    PARK
+
+[gcode_macro M76]                                                               # Marlin Compatibility
+gcode:
+    PAUSE
+
+[gcode_macro M601]                                                               # Marlin Compatibility
+gcode:
+    PAUSE
+
+[gcode_macro M300]                                                              # Marlin Compatibility
+gcode:
+    BEEP
+
+[gcode_macro M600]                                                              # Marlin Compatibility
+gcode:
+    FILAMENT_CHANGE
+
+[gcode_macro M701]                                                              # Marlin Compatibility
+gcode:
+    FILAMENT_LOAD
+
+[gcode_macro M702]                                                              # Marlin Compatibility
+gcode:
+    FILAMENT_UNLOAD
+
+[gcode_macro M92]
+gcode:
+    {% set extruder_steps = params.E|default(0.0025)|float %}
+    SET_EXTRUDER_STEP_DISTANCE DISTANCE={extruder_steps}
+
+[gcode_macro M204]                                                              # Set Acceleration
+# Klipper accepts M204 S<value> OR M204 P<value> T<value> where both P and T must be specified
+# PrusaSliser sends M204 P<value> without T and Klipper shows an error
+# This macro makes M204 command more versatile
+rename_existing: M204.1
+gcode:
+    {% set factor = params.F|default(0.5)|float %}
+    {% if 'S' in params %}
+        SET_VELOCITY_LIMIT ACCEL={S} ACCEL_TO_DECEL={ S|float * factor }
+    {% else %}
+        {% if 'P' in params %}
+            {% if 'T' in params %}
+                {% if P|int < T|int %}
+                    SET_VELOCITY_LIMIT ACCEL={P} ACCEL_TO_DECEL={ P|float * factor }
+                {% else %}
+                    SET_VELOCITY_LIMIT ACCEL={T} ACCEL_TO_DECEL={ T|float * factor }
+                {% endif %}
+            {% else %}
+                SET_VELOCITY_LIMIT ACCEL={P} ACCEL_TO_DECEL={ P|float * factor }
+            {% endif %}
+        {% elif 'T' in params %}
+            SET_VELOCITY_LIMIT ACCEL={T} ACCEL_TO_DECEL={ T|float * factor }
+        {% endif %}
+    {% endif %}
+
+[gcode_macro M205]                                                              # Set Junction deviation or Jerk
+gcode:
+    {% if 'J' in params %}
+        SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={J}
+    {% elif 'X' in params %}
+        SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={X}
+    {% elif 'Y' in params %}
+        SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={Y}
+    {% endif %}
+
+[gcode_macro M207]                                                              # Set Firmware Retraction
+gcode:
+    {% set length = params.S|default(0.5)|float %}
+    {% set speed = params.F|default(25)|float %}
+    SET_RETRACTION RETRACT_LENGTH={length} RETRACT_SPEED={speed}
+
+[gcode_macro M303]                                                              # PID Autotune
+gcode:
+    {% if 'E' in params %}
+        {% set heater = params.E|default(0)|int %}
+        {% set temp = params.T|default(0)|float %}
+        {% if heater == 0 %}                                                    # extruder
+            {% if temp >= printer.configfile.settings.extruder.min_extrude_temp|float %}
+                {% if temp <= printer.configfile.settings.extruder.max_temp|float %}
+                    PID_CALIBRATE HEATER=extruder TARGET={T}
+                {% endif %}
+            {% endif %}
+        {% elif heater == -1 %}                                                 # bed
+            {% if temp <= printer.configfile.settings.heater_bed.max_temp|float %}
+                PID_CALIBRATE HEATER=heater_bed TARGET={T}
+            {% endif %}
+        {% endif %}
+    {% endif %}
+
+[gcode_macro M486]                                                              # Label Objects
+# M486 has no realization in Klipper yet
+# This empty macro stops M486-error terminal messages
+gcode:
+    # Do nothing
+
+[gcode_macro M500]                                                              # Save Settings
+gcode:
+    SAVE_CONFIG
+
+[gcode_macro M900]                                                              # Set Pressure Advance
+gcode:
+    {% if 'K' in params %}
+        SET_PRESSURE_ADVANCE ADVANCE={ params.K|float }
+    {% endif %}

Flying Bear Generic Configs/macros/prime_line.cfg

@@ -0,0 +1,45 @@
+################################################################################
+# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
+# Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
+# G-code Macros by ODUCCEU
+################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
+
+# Wipe the nozzle ##############################################################
+
+[gcode_macro PRIME_LINE]
+gcode: 
+    {% set feedrate = params.F|default(10)|float * 60 %}
+    {% set length = 100.0 %}
+    {% set width = printer.configfile.settings.extruder.nozzle_diameter|float * 1.1 %}
+    {% set height = ( (width / 0.04)|int - (width / 0.04 / 4)|int )|float * 0.04 %}
+    {% set extrude = 2 * length * width * height / 2.4 %}
+    {% if 'Y' in params %}
+        {% set x_start = 1.0 %}
+        {% set y_start = (printer.toolhead.axis_maximum.y|float - 100) / 2 %}
+    {% else %}
+        {% set x_start = (printer.toolhead.axis_maximum.x|float - 100) / 2 %}
+        {% set y_start = 1.0 %}
+    {% endif %}
+    SAVE_GCODE_STATE NAME=PRIME_LINE_STATE
+    SET_IDLE_TIMEOUT TIMEOUT=7200
+    G0 Z0 F600 
+    G0 Y1 F12000                                                                # cut the crap
+    G0 Z10 F600 
+    G0 X{x_start} Y{y_start} F6000                                              # move to start position
+    G0 Z{height} F600 
+    G91                                                                         # relative positioning
+    {% if 'Y' in params %}
+        G1 Y100 E{extrude} F{feedrate}                                          # prime
+        G1 Y-100 F12000                                                         # wipe
+    {% else %}
+        G1 X100 E{extrude} F{feedrate}                                          # prime
+        G1 X-100 F12000                                                         # wipe
+    {% endif %}
+    G0 Z10 F600 
+    RESTORE_GCODE_STATE NAME=PRIME_LINE_STATE
+
+################################################################################

Flying Bear Generic Configs/macros/print_management.cfg

@@ -3,14 +3,18 @@
 # Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
 # G-code Macros by ODUCCEU
 ################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
 
 # Print Job Management #########################################################
 
 [gcode_macro START_PRINT]
-## PrusaSliser: 
+## PrusaSliser/SuperSlicer: 
 # M190 S0
 # M109 S0
-# START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP={first_layer_bed_temperature}
+# START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP={first_layer_bed_temperature[0]}
 ## Cura: 
 # M190 S0
 # M109 S0
@@ -30,17 +34,15 @@ gcode:
     M220 S100                                                                   # reset feedrate
     M221 S100                                                                   # reset flowrate
     G90                                                                         # absolute positioning
-    M82                                                                         # relative extrusion mode
+    M83                                                                         # relative extrusion mode
     SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}                  # set bed temp
     TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp_preheat}               # wait until bed is partially heated
     SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}               # set extruder temp
     TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp}                       # wait for bed temp
     TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}                    # wait for extruder temp
     G28                                                                         # home
-    G0 Z10 F1500                                                                # raise Z
+    G0 Z10 F600                                                                 # raise Z
-    G92 E0                                                                      # reset extruder
+    G1 E{E} F2100                                                               # prime
-    G1 E{E} F1500                                                               # prime
-    G92 E0                                                                      # reset extruder
 
 [gcode_macro END_PRINT]
 gcode:
@@ -48,15 +50,14 @@ gcode:
     TURN_OFF_HEATERS
     M107                                                                        # turn off fan
     G91                                                                         # relative positioning
-    G1 E-{E} F1500                                                              # retract
+    G1 E-{E} F2100                                                              # retract
-    G0 X1 Y1 F5000                                                              # wipe
+    G0 X1 Y1 F6000                                                              # wipe
-    G0 Z2 F1500                                                                 # raise Z
+    G0 Z2 F600                                                                  # raise Z
     G90                                                                         # absolute positioning
     PARK Z=30
     M84                                                                         # turn off all motors
     BEEP P=200 S=250
-    # NORMAL_SPEED                                                                # reset stepper current
+    SAVE_UPDATES
-    # SAVE_IF_SET                                                                 # SAVE_CONFIG
 
 [gcode_macro PARK]
 gcode:
@@ -78,8 +79,8 @@ gcode:
     SAVE_GCODE_STATE NAME=PARK_STATE
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     G90                                                                         # absolute positioning
-    G0 Z{z_park} F1500
+    G0 Z{z_park} F600 
-    G0 X{x_park} Y{y_park} F5000
+    G0 X{x_park} Y{y_park} F6000
     RESTORE_GCODE_STATE name=PARK_STATE
 
 [gcode_macro PAUSE]
@@ -129,7 +130,7 @@ gcode:
     {% if printer.extruder.can_extrude|lower == 'true' %}
         G91                                                                     # relative positioning
         G1 E-{E} F2100                                                          # retract
-        G0 Z2 F1500                                                             # raise Z
+        G0 Z2 F600                                                              # raise Z
         G90                                                                     # absolute positioning
     {% else %}
         {action_respond_info("Extruder is not hot enough")}
@@ -138,6 +139,16 @@ gcode:
     BASE_CANCEL_PRINT
     PARK Z=30
     M84                                                                         # turn off all motors
-    # NORMAL_SPEED                                                                # reset stepper current
+
+# Save to Config ##########################################################
+
+[gcode_macro SAVE_UPDATES]
+description: Run SAVE_CONFIG if there are updates that it may persist to disk
+gcode:
+    {% if printer.configfile.save_config_pending %}
+        M118 Saving and restarting now
+        G4 P2000                                                                # wait 2 seconds
+        SAVE_CONFIG
+    {% endif %}
 
 ################################################################################

Flying Bear Generic Configs/printer/fb-ghost4s-bltouch.cfg

@@ -87,8 +87,8 @@ screw3: 229,206
 screw3_name: back right screw
 screw4: 26,206
 screw4_name: back left screw
-horizontal_move_z: 10
 speed: 100
+horizontal_move_z: 10
 screw_thread: CW-M3
 
 ################################################################################
@@ -100,7 +100,6 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BED_MESH_CALIBRATE
     G0 X0 Y0 F6000
-    SAVE_AFTER_ALL
 
 [gcode_macro PROBE_CALIBRATE]                                                   # Calibrate Z-offset
 rename_existing: BASE_PROBE_CALIBRATE
@@ -108,19 +107,45 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BASE_PROBE_CALIBRATE
 
-# Save Mesh to Config ##########################################################
+## Replace START_PRINT macro ###################################################
 
-[gcode_macro SAVE_AFTER_ALL]
+[gcode_macro START_PRINT]
-variable_save: 0
+## PrusaSliser: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP={first_layer_bed_temperature} MESH_DO=<1|0>
+## Cura: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={material_print_temperature_layer_0} BED_TEMP={material_bed_temperature_layer_0} MESH_DO=<1|0>
+description: Start routine for the print
+variable_retract: 10
 gcode:
-    SET_GCODE_VARIABLE MACRO=SAVE_AFTER_ALL VARIABLE=save VALUE=1
+    {% set extruder_temp = params.EXTRUDER_TEMP|default(240)|float %}
- 
+    {% set bed_temp = params.BED_TEMP|default(70)|float %}
-[gcode_macro SAVE_IF_SET]
+    {% set E = printer["gcode_macro START_PRINT"].retract|float %}
-gcode:
+    {% set mesh = params.MESH_DO|default(0)|int %}
-    {% if printer["gcode_macro SAVE_AFTER_ALL"].save == 1 %}
+    CLEAR_PAUSE
-        G4 P2000                                                                # dwell 2 seconds
+    M220 S100                                                                   # reset feedrate
-        {action_respond_info("Saving and restarting now")}
+    M221 S100                                                                   # reset flowrate
-        SAVE_CONFIG
+    G90                                                                         # absolute positioning
+    M82                                                                         # relative extrusion mode
+    SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}                  # set bed temp
+    TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp}                       # wait for bed temp
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}               # set extruder temp
+    G28                                                                         # home
+    {% if 'MESH_DO' in params %}
+        {% if mesh == 0 %}
+            BED_MESH_PROFILE LOAD={bed_temp}                                    # load existing mesh
+        {% else %}
+            G29                                                                 # do G29 while heating extruder
+            BED_MESH_PROFILE SAVE={bed_temp}
         {% endif %}
+    {% endif %}
+    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}                    # wait for extruder temp
+    G0 Z10 F1500                                                                # raise Z
+    G92 E0                                                                      # reset extruder
+    G1 E{E} F1500                                                               # prime
+    G92 E0                                                                      # reset extruder
 
 ################################################################################

Flying Bear Generic Configs/printer/fb-ghost4s.cfg

@@ -30,7 +30,7 @@ homing_retract_dist: 0
 
 [stepper_y]
 step_pin: Y_STEP_PIN
-dir_pin: !Y_DIR_PIN
+dir_pin: Y_DIR_PIN
 enable_pin: !Y_ENABLE_PIN
 rotation_distance: 40
 microsteps: 16
@@ -42,12 +42,12 @@ homing_speed: 100
 homing_retract_dist: 0                                                          # disable for head retraction after homing
 
 [stepper_z]                                                                     # left stepper
-step_pin: Z1_STEP_PIN
+step_pin: Z_STEP_PIN
-dir_pin: !Z1_DIR_PIN
+dir_pin: !Z_DIR_PIN
-enable_pin: !Z1_ENABLE_PIN
+enable_pin: !Z_ENABLE_PIN
 rotation_distance: 8
 microsteps: 16
-endstop_pin: !Z1_STOP_PIN
+endstop_pin: !Z_STOP_PIN
 position_max: 200                                                               # Z-axis print volume size
 homing_speed: 20
 second_homing_speed: 5

Flying Bear Generic Configs/printer/fb-ghost5-bltouch.cfg

@@ -87,8 +87,8 @@ screw3: 230,180
 screw3_name: back right screw
 screw4: 25,180
 screw4_name: back left screw
-horizontal_move_z: 10
 speed: 100
+horizontal_move_z: 10
 screw_thread: CW-M4
 
 ################################################################################
@@ -100,7 +100,6 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BED_MESH_CALIBRATE
     G0 X0 Y0 F6000
-    SAVE_AFTER_ALL
 
 [gcode_macro PROBE_CALIBRATE]                                                   # Calibrate Z-offset
 rename_existing: BASE_PROBE_CALIBRATE
@@ -108,19 +107,45 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BASE_PROBE_CALIBRATE
 
-# Save Mesh to Config ##########################################################
+## Replace START_PRINT macro ###################################################
 
-[gcode_macro SAVE_AFTER_ALL]
+[gcode_macro START_PRINT]
-variable_save: 0
+## PrusaSliser: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP={first_layer_bed_temperature} MESH_DO=<1|0>
+## Cura: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={material_print_temperature_layer_0} BED_TEMP={material_bed_temperature_layer_0} MESH_DO=<1|0>
+description: Start routine for the print
+variable_retract: 10
 gcode:
-    SET_GCODE_VARIABLE MACRO=SAVE_AFTER_ALL VARIABLE=save VALUE=1
+    {% set extruder_temp = params.EXTRUDER_TEMP|default(240)|float %}
- 
+    {% set bed_temp = params.BED_TEMP|default(70)|float %}
-[gcode_macro SAVE_IF_SET]
+    {% set E = printer["gcode_macro START_PRINT"].retract|float %}
-gcode:
+    {% set mesh = params.MESH_DO|default(0)|int %}
-    {% if printer["gcode_macro SAVE_AFTER_ALL"].save == 1 %}
+    CLEAR_PAUSE
-        G4 P2000                                                                # dwell 2 seconds
+    M220 S100                                                                   # reset feedrate
-        {action_respond_info("Saving and restarting now")}
+    M221 S100                                                                   # reset flowrate
-        SAVE_CONFIG
+    G90                                                                         # absolute positioning
+    M82                                                                         # relative extrusion mode
+    SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}                  # set bed temp
+    TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp}                       # wait for bed temp
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}               # set extruder temp
+    G28                                                                         # home
+    {% if 'MESH_DO' in params %}
+        {% if mesh == 0 %}
+            BED_MESH_PROFILE LOAD={bed_temp}                                    # load existing mesh
+        {% else %}
+            G29                                                                 # do G29 while heating extruder
+            BED_MESH_PROFILE SAVE={bed_temp}
         {% endif %}
+    {% endif %}
+    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}                    # wait for extruder temp
+    G0 Z10 F1500                                                                # raise Z
+    G92 E0                                                                      # reset extruder
+    G1 E{E} F1500                                                               # prime
+    G92 E0                                                                      # reset extruder
 
 ################################################################################

Flying Bear Generic Configs/printer/fb-ghost5.cfg

@@ -30,7 +30,7 @@ homing_retract_dist: 0
 
 [stepper_y]
 step_pin: Y_STEP_PIN
-dir_pin: !Y_DIR_PIN
+dir_pin: Y_DIR_PIN
 enable_pin: !Y_ENABLE_PIN
 rotation_distance: 40
 microsteps: 16
@@ -42,12 +42,12 @@ homing_speed: 100
 homing_retract_dist: 0                                                          # disable for head retraction after homing
 
 [stepper_z]                                                                     # left stepper
-step_pin: Z1_STEP_PIN
+step_pin: Z_STEP_PIN
-dir_pin: !Z1_DIR_PIN
+dir_pin: !Z_DIR_PIN
-enable_pin: !Z1_ENABLE_PIN
+enable_pin: !Z_ENABLE_PIN
 rotation_distance: 8
 microsteps: 16
-endstop_pin: !Z1_STOP_PIN
+endstop_pin: !Z_STOP_PIN
 position_max: 200                                                               # Z-axis print volume size
 homing_speed: 20
 second_homing_speed: 5

Flying Bear Generic Configs/printer/fb-reborn-bltouch.cfg

@@ -102,8 +102,8 @@ screw3: 305,267.5
 screw3_name: back right screw
 screw4: 45,267.5
 screw4_name: back left screw
-horizontal_move_z: 10
 speed: 100
+horizontal_move_z: 10
 screw_thread: CW-M4
 
 ################################################################################
@@ -115,7 +115,6 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BED_MESH_CALIBRATE
     G0 X0 Y0 F6000
-    SAVE_AFTER_ALL
 
 [gcode_macro PROBE_CALIBRATE]                                                   # Calibrate Z-offset
 rename_existing: BASE_PROBE_CALIBRATE
@@ -123,19 +122,45 @@ gcode:
     {% if printer.toolhead.homed_axes != "xyz" %} G28 {% endif %}               # home if not homed
     BASE_PROBE_CALIBRATE
 
-# Save Mesh to Config ##########################################################
+## Replace START_PRINT macro ###################################################
 
-[gcode_macro SAVE_AFTER_ALL]
+[gcode_macro START_PRINT]
-variable_save: 0
+## PrusaSliser: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP={first_layer_bed_temperature} MESH_DO=<1|0>
+## Cura: 
+# M190 S0
+# M109 S0
+# START_PRINT EXTRUDER_TEMP={material_print_temperature_layer_0} BED_TEMP={material_bed_temperature_layer_0} MESH_DO=<1|0>
+description: Start routine for the print
+variable_retract: 10
 gcode:
-    SET_GCODE_VARIABLE MACRO=SAVE_AFTER_ALL VARIABLE=save VALUE=1
+    {% set extruder_temp = params.EXTRUDER_TEMP|default(240)|float %}
- 
+    {% set bed_temp = params.BED_TEMP|default(70)|float %}
-[gcode_macro SAVE_IF_SET]
+    {% set E = printer["gcode_macro START_PRINT"].retract|float %}
-gcode:
+    {% set mesh = params.MESH_DO|default(0)|int %}
-    {% if printer["gcode_macro SAVE_AFTER_ALL"].save == 1 %}
+    CLEAR_PAUSE
-        G4 P2000                                                                # dwell 2 seconds
+    M220 S100                                                                   # reset feedrate
-        {action_respond_info("Saving and restarting now")}
+    M221 S100                                                                   # reset flowrate
-        SAVE_CONFIG
+    G90                                                                         # absolute positioning
+    M82                                                                         # relative extrusion mode
+    SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}                  # set bed temp
+    TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp}                       # wait for bed temp
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}               # set extruder temp
+    G28                                                                         # home
+    {% if 'MESH_DO' in params %}
+        {% if mesh == 0 %}
+            BED_MESH_PROFILE LOAD={bed_temp}                                    # load existing mesh
+        {% else %}
+            G29                                                                 # do G29 while heating extruder
+            BED_MESH_PROFILE SAVE={bed_temp}
         {% endif %}
+    {% endif %}
+    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}                    # wait for extruder temp
+    G0 Z10 F1500                                                                # raise Z
+    G92 E0                                                                      # reset extruder
+    G1 E{E} F1500                                                               # prime
+    G92 E0                                                                      # reset extruder
 
 ################################################################################