jeka/OTGateway
1
0
Fork 0
mirror of https://github.com/Laxilef/OTGateway.git synced 2025-12-10 18:24:27 +05:00
Code Issues Packages Projects Releases Wiki Activity

upd readme, bump version

Browse Source
This commit is contained in:
Yurii
2023-11-17 22:14:45 +03:00
parent 7c5810e6d1
commit ee5c6fc953
3 changed files with 13 additions and 3 deletions
Download Patch File Download Diff File Expand all files Collapse all files

12
README.md
View File

@@ -89,7 +89,7 @@ The outdoor temperature sensor must be connected to the **TEMP1** connector, the
5. Set up a connection to your MQTT server: ip, port, user, password 5. Set up a connection to your MQTT server: ip, port, user, password
6. Set up a **Opentherm pin IN** & **Opentherm pin OUT**. No change for my board. Typically used **IN** = 4, **OUT** = 5 6. Set up a **Opentherm pin IN** & **Opentherm pin OUT**. No change for my board. Typically used **IN** = 4, **OUT** = 5
7. Set up a **Outdoor sensor pin** & **Indoor sensor pin**. No change for my board. 7. Set up a **Outdoor sensor pin** & **Indoor sensor pin**. No change for my board.
8. if necessary, set up a the master member ID ([see more](#tested-on)) 8. if necessary, set up a the Master Member ID ([see more](#tested-on))
9. Restart module (required after changing OT pins and/or sensors pins!) 9. Restart module (required after changing OT pins and/or sensors pins!)
After connecting to your wifi network, you can go to the setup page at the address that ESP8266 received. After connecting to your wifi network, you can go to the setup page at the address that ESP8266 received.
@@ -165,6 +165,16 @@ If your boiler does not support the installation of an outdoor temperature senso
</details> </details>
After these settings, you can enable the "Equitherm" and/or "PID" modes and configure them as described below. After these settings, you can enable the "Equitherm" and/or "PID" modes and configure them as described below.
## Troubleshooting
**Q:** Controller in monitor/readon mode (cannot set temperature, etc.)<br>
**A:** Try changing the "Master Member ID", this is most likely the problem. If you don't know which identifier is valid for your boiler, you need to use brute force.
**Q:** The boiler does not respond to setting the heating temperature.<br>
**A:** Try checking the "Opentherm summer/winter mode", "Opentherm CH2 enabled", "Opentherm heating CH1 to CH2" checkboxes one by one and all together on the "setup" page. If this doesn't work, see above.
**Q:** My boiler does not have a hot water heating function. How to turn it off?<br>
**A:** Uncheck "Opentherm DHW present" on the "setup" page.
## About modes ## About modes
### Equitherm ### Equitherm

2
platformio.ini
View File

@@ -25,7 +25,7 @@ lib_deps =
build_flags = -D PIO_FRAMEWORK_ARDUINO_LWIP2_HIGHER_BANDWIDTH -mtext-section-literals build_flags = -D PIO_FRAMEWORK_ARDUINO_LWIP2_HIGHER_BANDWIDTH -mtext-section-literals
upload_speed = 921600 upload_speed = 921600
monitor_speed = 115200 monitor_speed = 115200
version = 1.3.3 version = 1.3.4
; Defaults ; Defaults
[esp8266_defaults] [esp8266_defaults]

2
src/defines.h
View File

@@ -1,4 +1,4 @@
#define OT_GATEWAY_VERSION "1.3.3" #define OT_GATEWAY_VERSION "1.3.4"
#define OT_GATEWAY_REPO "https://github.com/Laxilef/OTGateway" #define OT_GATEWAY_REPO "https://github.com/Laxilef/OTGateway"
#define AP_SSID "OpenTherm Gateway" #define AP_SSID "OpenTherm Gateway"
#define AP_PASSWORD "otgateway123456" #define AP_PASSWORD "otgateway123456"