Updates and fixes

update /macros folder

Update *bltouch.cfg

Fix Z and Y pins

Fix Y direction

Update MKSRN-Sv1.3 pins

Clean obsolete comments

Flying Bear Generic Configs/macros/filament_management.cfg

@@ -0,0 +1,111 @@
+################################################################################
+# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
+# Printer: Flying Bear Ghost 4S / Ghost 5 / Reborn
+# G-code Macros by ODUCCEU
+################################################################################
+# WARNING! DO NOT EDIT THIS FILE!
+# To override settings from this file, you can copy and paste the relevant
+# sections into your printer.cfg and change it there.
+################################################################################
+
+# Filament Change ##############################################################
+
+[gcode_macro FILAMENT_CHANGE]
+# Unloads filament, waites 5 minutes for manual filament switch and loads again
+gcode:
+    SAVE_GCODE_STATE NAME=FILAMENT_CHANGE_STATE
+    {% set timer = params.T|default(300)|float %}
+    {% set unload = params.U|default(100)|float %}
+    {% set load = params.L|default(100)|float %}
+    {% if printer.pause_resume.is_paused %}
+        M118 Already paused
+    {% else %}
+        {% if printer.toolhead.homed_axes != "xyz" %}
+            M118 Homing
+            G28                                                                 # home if not homed
+        {% else %}
+            M118 Pausing print
+            PAUSE
+        {% endif %}
+    {% endif %}
+    M118 Changing filament...
+    SET_IDLE_TIMEOUT TIMEOUT=7200
+    FILAMENT_UNLOAD U={unload}
+    COUNTDOWN TIME={timer} MSG="Change filament! Time left: "
+    FILAMENT_LOAD L={load}
+    RESTORE_GCODE_STATE NAME=FILAMENT_CHANGE_STATE
+
+[gcode_macro FILAMENT_LOAD]
+gcode:
+    {% set load = params.L|default(100)|float * 0.5 %}
+    {% set extruder_temp = params.T|default(220)|float %}
+    SAVE_GCODE_STATE NAME=FILAMENT_LOAD_STATE
+    LOW_TEMP_CHECK T={extruder_temp}
+    M118 Loading filament...
+    M83                                                                         # relative extrusion
+    G0 E{load} F600                                                             # load the filament into the hotend area
+    G4 P1000                                                                    # wait 1 second
+    G1 E50 F100                                                                 # purge
+    M400                                                                        # wait until all moves are completed
+    M118 Filament loaded!
+    BEEP
+    RESTORE_GCODE_STATE NAME=FILAMENT_LOAD_STATE
+
+[gcode_macro FILAMENT_UNLOAD]
+gcode:
+    {% set unload = params.U|default(100)|float %}
+    {% set extruder_temp = params.T|default(220)|float %}
+    SAVE_GCODE_STATE NAME=FILAMENT_UNLOAD_STATE
+    LOW_TEMP_CHECK T={extruder_temp}
+    M118 Unloading filament
+    M83                                                                         # relative extrusion
+    G0 E-5 F3600                                                                # extract filament to the coldend zone 
+    G4 P3000                                                                    # wait for 3 seconds
+    G0 E5 F3600                                                                 # push back the filament to smash any stringing 
+    G0 E-15 F3600                                                               # extract back fast to the coldend zone 
+    G0 E-{unload} F300                                                          # extract a lot
+    M400                                                                        # wait until all moves are completed
+    M118 Filament unloaded!
+    BEEP
+    RESTORE_GCODE_STATE NAME=FILAMENT_UNLOAD_STATE
+
+[gcode_macro LOW_TEMP_CHECK]
+gcode:
+    {% set extruder_temp = params.T|default(220)|float %}
+    {% if printer.extruder.target > extruder_temp %}                            # check for a setpoint for extruder
+        {% set extruder_temp = printer.extruder.target %}
+    {% endif %}
+    {% if printer.extruder.temperature < extruder_temp %}                       # heat to the target temp
+        M118 Heating to {extruder_temp}
+        SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}
+        TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp}
+    {% endif %}
+
+[gcode_macro COUNTDOWN]
+gcode: 
+    {% set timer = params.TIME|default(10)|int %}
+    {% set message = params.MSG|default("Time: ") %}
+    # countdown
+    {% if timer > 60 %}
+        {% for s in range(timer, 60, -10) %}
+            M118 {message} {s}s
+            G4 P10000                                                           # wait 10 seconds
+        {% endfor %}
+        {% set timer = 60 %}
+    {% endif %}
+    {% if timer > 10 %}
+        {% for s in range(timer, 10, -5) %}
+            M118 {message} {s}s
+            G4 P5000                                                            # wait 5 seconds
+        {% endfor %}
+        {% set timer = 10 %}
+    {% endif %}
+    {% if timer > 0 %}
+        {% for s in range(timer, 0, -1) %}
+            M118 {message} {s}s
+            G4 P1000                                                            # wait 1 second
+        {% endfor %}
+    {% endif %}
+    BEEP
+
+################################################################################