mirror of
https://github.com/oducceu/klipper_configs.git
synced 2025-12-11 18:24:28 +05:00
Add mks-rn-s-13-E-on-5.cfg
Add config for MKS Robin Nano-S v1.3 with extruder plugged to E1
This commit is contained in:
oducceu
@@ -1,5 +1,5 @@
|
||||
################################################################################
|
||||
# Board: MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
|
||||
# Board: MKS Robin Nano v1.3
|
||||
# Config by ODUCCEU
|
||||
################################################################################
|
||||
# WARNING! DO NOT EDIT THIS FILE!
|
||||
|
||||
162
Flying Bear Generic Configs/board/mks-rn-s-13-E-on-5.cfg
Normal file
162
Flying Bear Generic Configs/board/mks-rn-s-13-E-on-5.cfg
Normal file
@@ -0,0 +1,162 @@
|
||||
################################################################################
|
||||
# Board: MKS Robin Nano-S v1.3 with extruder plugged to E1
|
||||
# Config by ODUCCEU
|
||||
################################################################################
|
||||
# WARNING! DO NOT EDIT THIS FILE!
|
||||
# To override settings from this file, you can copy and paste the relevant
|
||||
# sections into your printer.cfg and change it there.
|
||||
################################################################################
|
||||
|
||||
# Documentation
|
||||
# https://www.klipper3d.org/Config_Reference.html
|
||||
|
||||
################################################################################
|
||||
# Firmware Configuration for MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
|
||||
################################################################################
|
||||
|
||||
# Reference
|
||||
# https://github.com/KevinOConnor/klipper/blob/master/config/generic-mks-robin-nano-v1.cfg
|
||||
#
|
||||
# ——————————————————————————————————————————————————————————————————————————————
|
||||
# Klipper Firmware Configuration
|
||||
# ——————————————————————————————————————————————————————————————————————————————
|
||||
# [*] Enable extra low-level configuration options
|
||||
# Micro-controller Architecture (STMicroelectronics STM32) --->
|
||||
# Processor model (STM32F407) --->
|
||||
# Bootloader offset (32KiB bootloader) --->
|
||||
# Clock Reference (8 MHz crystal) --->
|
||||
# Communication interface (Serial (on USART3 PB11/PB10)) --->
|
||||
# (250000) Baud rate for serial port
|
||||
# [ ] Specify a custom step pulse duration
|
||||
# () GPIO pins to set at micro-controller startup
|
||||
# ——————————————————————————————————————————————————————————————————————————————
|
||||
#
|
||||
# Select "Communication interface (Serial (on USART3 PB11/PB10))" for USB connection
|
||||
# Select "Communication interface (Serial (on USART1 PA10/PA9))" for UART using WiFi slot
|
||||
#
|
||||
# Note that the "make flash" command does not work with MKS Robin boards.
|
||||
# After running "make", no need to run py script, just rename the firmware file:
|
||||
# mv ~/klipper/out/klipper.bin ~/klipper/out/Robin_nano35.bin
|
||||
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
|
||||
# printer with that SD card inserted.
|
||||
|
||||
################################################################################
|
||||
# Pin Definitions for MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
|
||||
################################################################################
|
||||
|
||||
# Reference for MKS Robin Nano v1.3
|
||||
# https://github.com/makerbase-mks/MKS-Robin-Nano-V1.X/blob/master/hardware/MKS%20Robin%20Nano%20V1.3_002/MKS%20Robin%20Nano%20V1.3_002%20PIN.pdf
|
||||
|
||||
# Reference for MKS Robin Nano-S v1.3
|
||||
# https://github.com/makerbase-mks/MKS-Robin-Nano-V1.X/blob/master/hardware/MKS%20Robin%20Nano-S%20V1.3_001/MKS%20Robin%20Nano-S%20V1.3_001%20PIN.pdf
|
||||
|
||||
## X_STEP PE3
|
||||
## X_DIR PE2
|
||||
## X_ENABLE PE4
|
||||
## X_STOP PA15
|
||||
|
||||
## Y_STEP PE0
|
||||
## Y_DIR PB9
|
||||
## Y_ENABLE PE1
|
||||
## Y_STOP PA12
|
||||
|
||||
## Z_STEP PB5
|
||||
## Z_DIR PB4
|
||||
## Z_ENABLE PB8
|
||||
## Z_MIN_STOP PA11
|
||||
## Z_MAX_STOP PC4
|
||||
|
||||
## E0_STEP PD6
|
||||
## E0_DIR PD3
|
||||
## E0_ENABLE PB3
|
||||
|
||||
## E1_STEP PA6 # Z1_STEP
|
||||
## E1_DIR PA1 # Z1_DIR
|
||||
## E1_ENABLE PA3 # Z1_ENABLE
|
||||
|
||||
## HE0 PC3
|
||||
## HE1 PB0 # HE0_FAN
|
||||
## BED PA0
|
||||
## TH1 (HE0 Temp) PC1
|
||||
## TH2 (HE1 Temp) PC2
|
||||
## TB (BED Temp) PC0
|
||||
|
||||
## FAN PB1
|
||||
|
||||
## MT_DET1 PA4
|
||||
## MT_DET2 PE6
|
||||
## PW_DET PA2
|
||||
## PB2 PB2
|
||||
|
||||
## SERVO PA8
|
||||
## BEEPER PC5
|
||||
|
||||
## WiFi_IO0 P13
|
||||
## WiFi_IO1 PC7
|
||||
## WiFi_TX PA9
|
||||
## WiFi_RX PA10
|
||||
|
||||
## USB_TX PB10
|
||||
## USB_RX PB11
|
||||
|
||||
################################################################################
|
||||
# Pin Aliases
|
||||
################################################################################
|
||||
|
||||
[board_pins mks_rn_13]
|
||||
aliases:
|
||||
## Steppers ####################################################################
|
||||
X_STEP_PIN=PE3, X_DIR_PIN=PE2, X_ENABLE_PIN=PE4, X_STOP_PIN=PA15,
|
||||
Y_STEP_PIN=PE0, Y_DIR_PIN=PB9, Y_ENABLE_PIN=PE1, Y_STOP_PIN=PA12,
|
||||
Z_STEP_PIN=PB5, Z_DIR_PIN=PB4, Z_ENABLE_PIN=PB8, Z_STOP_PIN=PA11,
|
||||
Z1_STEP_PIN=PD6, Z1_DIR_PIN=PD3, Z1_ENABLE_PIN=PB3, Z1_STOP_PIN=PC4,
|
||||
E0_STEP_PIN=PA6, E0_DIR_PIN=PA1, E0_ENABLE_PIN=PA3,
|
||||
## Heaters #####################################################################
|
||||
E_HEATER_PIN=PC3, E_SENSOR_PIN=PC1,
|
||||
BED_HEATER_PIN=PA0, BED_SENSOR_PIN=PC0,
|
||||
## Fans ########################################################################
|
||||
HEATER_FAN_PIN=PB0,
|
||||
PARTCOOLING_FAN_PIN=PB1,
|
||||
## Controls ####################################################################
|
||||
MT_DET1_PIN=PA4, MT_DET2_PIN=PE6,
|
||||
PW_DET_PIN=PA2, AUTO_OFF_PIN=PB2,
|
||||
## BLTouch #####################################################################
|
||||
BLTOUCH_SENSOR_PIN=PE6, # MT_DET2
|
||||
BLTOUCH_CONTROL_PIN=PA8, # SERVO
|
||||
## TMC2209 UART ################################################################
|
||||
TMC_UART_PIN=PA1, TMC_TX_PIN=PA6,
|
||||
|
||||
################################################################################
|
||||
# MCU
|
||||
################################################################################
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 # USB
|
||||
restart_method: command
|
||||
|
||||
################################################################################
|
||||
# Sensors
|
||||
################################################################################
|
||||
|
||||
[temperature_sensor board]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
[filament_switch_sensor filament_sensor]
|
||||
switch_pin: PA4
|
||||
runout_gcode:
|
||||
BEEP P=1500
|
||||
|
||||
################################################################################
|
||||
# Beeper
|
||||
################################################################################
|
||||
|
||||
[output_pin _BEEPER_pin]
|
||||
pin: PC5
|
||||
pwm: True
|
||||
value: 0
|
||||
shutdown_value: 0
|
||||
cycle_time: 0.001
|
||||
|
||||
################################################################################
|
||||
@@ -1,5 +1,5 @@
|
||||
################################################################################
|
||||
# Board: MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
|
||||
# Board: MKS Robin Nano-S v1.3
|
||||
# Config by ODUCCEU
|
||||
################################################################################
|
||||
# WARNING! DO NOT EDIT THIS FILE!
|
||||
|
||||
@@ -28,15 +28,16 @@
|
||||
|
||||
## Control board ###############################################################
|
||||
# THERE CAN BE ONLY ONE!
|
||||
# [include board/mks-rn-11.cfg]
|
||||
[include board/mks-rn-13.cfg]
|
||||
# [include board/mks-rn-s-13.cfg]
|
||||
# [include board/mks-rn-11.cfg] # MKS Robin Nano v1.1
|
||||
[include board/mks-rn-13.cfg] # MKS Robin Nano v1.3
|
||||
# [include board/mks-rn-s-13.cfg] # MKS Robin Nano-S v1.3
|
||||
# [include board/mks-rn-s-13-E-on-5.cfg] # MKS Robin Nano-S v1.3 with extruder plugged to E1
|
||||
|
||||
## Base configuration ##########################################################
|
||||
[include printer/fb-reborn.cfg]
|
||||
|
||||
## Drivers #####################################################################
|
||||
[include printer/tmc2225.cfg]
|
||||
[include printer/tmc2225.cfg] # enable for MKS Robin Nano v1.3, disable for MKS Robin Nano-S v1.3
|
||||
|
||||
## Base macros #################################################################
|
||||
[include macros/macros.cfg]
|
||||
|
||||
Reference in New Issue
Block a user