diff --git a/steel_data/config/jschuh_klipper_macros.cfg b/steel_data/config/jschuh_klipper_macros.cfg
index 2bc6596..8e7e102 100644
--- a/steel_data/config/jschuh_klipper_macros.cfg
+++ b/steel_data/config/jschuh_klipper_macros.cfg
@@ -21,7 +21,7 @@ gcode: # This line is required by Klipper.
 # for these macros. For example, you could uncomment the following line to
 # automatically adjust your bed surface offsets to account for any changes made
 # to your Z endstop or probe offset.
-  ADJUST_SURFACE_OFFSETS
+# ADJUST_SURFACE_OFFSETS
 
 [gcode_macro update_git]
 gcode:
@@ -46,9 +46,9 @@ verbose: True
 [include klipper-macros/*.cfg]
 # Uncomment to include features that require specific hardware support.
 # LCD menu support for features like bed surface selection and pause next layer.
-#[include klipper-macros/optional/lcd_menus.cfg]
+[include klipper-macros/optional/lcd_menus.cfg]
 # Optimized bed leveling
-#[include klipper-macros/optional/bed_mesh.cfg]
+[include klipper-macros/optional/bed_mesh.cfg]
 
 # The sections below here are required for the macros to work. If your config
 # already has some of these sections you should merge the duplicates into one
@@ -70,4 +70,4 @@ on_error_gcode: CANCEL_PRINT
 
 [display_status]
 
-[exclude_object]
\ No newline at end of file
+[exclude_object]
diff --git a/steel_data/config/printer.cfg b/steel_data/config/printer.cfg
index 7686e9d..1560e42 100644
--- a/steel_data/config/printer.cfg
+++ b/steel_data/config/printer.cfg
@@ -13,8 +13,8 @@ serial: /dev/ttySteel
 [bed_mesh]
 speed: 60
 horizontal_move_z: 5
-mesh_min: 6,12
-mesh_max: 176,162
+mesh_min: 0,0
+mesh_max: 185,168
 probe_count: 3, 3
 mesh_pps: 2, 2
 fade_start: 1
@@ -34,14 +34,10 @@ screw4_name: Rear right screw
 [screws_tilt_adjust]
 horizontal_move_z: 3
 speed: 60
-screw1: 20,150
-screw1_name: back left
+screw1: 20,0
 screw2: 190,150
-screw2_name: back right
-screw3: 20,0
-screw3_name: front left
+screw3: 20,150
 screw4: 190,0
-screw4_name: front right
 screw_thread: CW-M3
 
 [bltouch]
@@ -58,7 +54,7 @@ pin_up_reports_not_triggered: True
 pin_up_touch_mode_reports_triggered: True
 
 [safe_z_home]
-home_xy_position: 105, 105# Change coordinates to the center of your print bed
+home_xy_position: 96.5, 107.5# Change coordinates to the center of your print bed
 speed: 50
 z_hop: 10 # Move up 10mm
 z_hop_speed: 5
@@ -70,8 +66,8 @@ enable_pin: !PD7
 microsteps: 16
 rotation_distance: 32
 endstop_pin: ^!PE4
-position_endstop: 200
-position_max: 200
+position_endstop: 193
+position_max: 193
 position_min: 0
 homing_speed: 50
  
@@ -82,9 +78,9 @@ enable_pin: !PF2
 microsteps: 16
 rotation_distance: 32
 endstop_pin: ^!PJ0
-position_endstop: 200
-position_max: 200
-position_min: 0
+position_endstop: 210
+position_max: 210
+position_min: -30
 homing_speed: 50
  
 [stepper_z]
@@ -97,7 +93,7 @@ endstop_pin: ^!PD3
 #position_endstop: 0.0
 endstop_pin: probe:z_virtual_endstop
 position_max: 270
-position_min: -5
+position_min: -10
 homing_speed: 20
  
 [extruder]
@@ -187,25 +183,22 @@ aliases:
 #*# pid_ki = 2.352
 #*# pid_kd = 86.791
 #*#
-#*# [stepper_z]
-#*# position_endstop = 4.180
-#*#
 #*# [bltouch]
-#*# z_offset = 1.330
+#*# z_offset = 0.950
 #*#
 #*# [bed_mesh default]
 #*# version = 1
 #*# points =
-#*# 	  -0.161375, -0.108500, -0.073500
-#*# 	  -0.004250, 0.004625, -0.081375
-#*# 	  -0.114250, -0.068625, -0.141250
+#*# 	  0.003375, -0.020000, -0.053625
+#*# 	  0.030750, -0.001250, -0.051500
+#*# 	  -0.005125, 0.000500, -0.040375
 #*# x_count = 3
 #*# y_count = 3
 #*# mesh_x_pps = 2
 #*# mesh_y_pps = 2
 #*# algo = lagrange
 #*# tension = 0.2
-#*# min_x = 6.0
-#*# max_x = 176.0
-#*# min_y = 12.0
-#*# max_y = 162.0
+#*# min_x = 59.47019999999999
+#*# max_x = 140.5102
+#*# min_y = 59.470200000000006
+#*# max_y = 140.51020000000003