mirror of
https://github.com/oducceu/klipper_configs.git
synced 2025-12-11 18:24:28 +05:00
Update fan pin assignments for BIGTREETECH-SKR-mini-E3.cfg and tmc2209_uart_mks_rn.cfg
This commit is contained in:
sz77
@@ -29,8 +29,9 @@ aliases:
|
||||
E_HEATER_PIN=PC8, E_SENSOR_PIN=PA0,
|
||||
BED_HEATER_PIN=PC9, BED_SENSOR_PIN=PC4,
|
||||
## Fans ########################################################################
|
||||
HEATER_FAN_PIN=PB15,
|
||||
PARTCOOLING_FAN_PIN=PC7,
|
||||
HEATER_FAN_PIN=PC7,
|
||||
PARTCOOLING_FAN_PIN=PC6,
|
||||
FUN2_FAN_PIN=PB15,
|
||||
## Controls ####################################################################
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>,
|
||||
|
||||
113
Flying Bear Generic Configs/printer.cfg
Normal file
113
Flying Bear Generic Configs/printer.cfg
Normal file
@@ -0,0 +1,113 @@
|
||||
################################################################################
|
||||
# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
|
||||
# Printer: Flying Bear Ghost 5
|
||||
# Config by ODUCCEU
|
||||
################################################################################
|
||||
|
||||
# Documentation
|
||||
# https://www.klipper3d.org/Config_Reference.html
|
||||
|
||||
# Rename this file to 'printer.cfg'.
|
||||
# Enable proper 'Control board' in 'Included configs' section.
|
||||
|
||||
# It is recommended that you follow these steps to properly calibrate your printer:
|
||||
# 1) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
# 4) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
|
||||
################################################################################
|
||||
# Included configs
|
||||
################################################################################
|
||||
|
||||
# Duplicate parameters in included config files will override each other.
|
||||
# In this case, each next included file overwrites the previous one in the list.
|
||||
# 'printer.cfg' takes precedence over other included files.
|
||||
# Try to avoid changing the default files by adding or changing parameters in 'printer.cfg' below.
|
||||
# This does not apply to commented out parameters.
|
||||
|
||||
## Control board ###############################################################
|
||||
# THERE CAN BE ONLY ONE!
|
||||
[include board/BIGTREETECH-SKR-mini-E3.cfg] # MKS Robin Nano v1.1 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-11.jpg
|
||||
# [include board/mks-rn-13.cfg] # MKS Robin Nano v1.3 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-13.png
|
||||
# [include board/mks-rn-s-13.cfg] # MKS Robin Nano-S v1.3 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-s-13.png
|
||||
# [include board/mks-rn-s-13-E-on-5.cfg] # MKS Robin Nano-S v1.3 with extruder plugged to E1 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-s-13-E-on-5.png
|
||||
|
||||
## Base configuration ##########################################################
|
||||
[include printer/fb-ghost5.cfg]
|
||||
|
||||
## Drivers #####################################################################
|
||||
# [include printer/tmc2225.cfg]
|
||||
[include printer/tmc2209_uart_mks_rn.cfg] # enable if using TMC drivers via UART on MKS Robin Nano
|
||||
|
||||
## Base macros #################################################################
|
||||
[include macros/macros.cfg]
|
||||
|
||||
## Additional hardware #########################################################
|
||||
[include printer/fb-ghost5-bltouch.cfg] # disable 'position_endstop' in [stepper_z] section
|
||||
# [include printer/rpi_mcu.cfg] # enable ONLY after setting Pi as MCU https://www.klipper3d.org/RPi_microcontroller.html
|
||||
# [include printer/accelerometer.cfg] # requires "rpi.cfg"
|
||||
|
||||
[include mainsail.cfg]
|
||||
|
||||
################################################################################
|
||||
# X, Y, Z
|
||||
################################################################################
|
||||
|
||||
[stepper_x]
|
||||
homing_speed: 150
|
||||
|
||||
[stepper_y]
|
||||
homing_speed: 150
|
||||
|
||||
[stepper_z]
|
||||
#position_endstop: 0.5 # disable if using BLTouch to use 'probe:z_virtual_endstop'
|
||||
|
||||
################################################################################
|
||||
# E0, HB
|
||||
################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 7.600 # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html
|
||||
nozzle_diameter: 0.400
|
||||
pressure_advance: 0.000 # CAUTION! Calibrate using https://www.klipper3d.org/Pressure_Advance.html
|
||||
control: pid # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands
|
||||
pid_Kp: 30.891
|
||||
pid_Ki: 2.542
|
||||
pid_Kd: 93.830
|
||||
# min_extrude_temp: 0 # allow Cold Extrusion for extruder steps calibration
|
||||
|
||||
[heater_bed]
|
||||
control: pid # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands
|
||||
pid_Kp: 63.104
|
||||
pid_Ki: 2.350
|
||||
pid_Kd: 423.586
|
||||
|
||||
################################################################################
|
||||
# Printer
|
||||
################################################################################
|
||||
|
||||
[mcu]
|
||||
# serial: /dev/ttyAMA0 # enable if connected via UART1 on Pi3/PiZ
|
||||
# serial: /dev/ttyAMA1 # enable if connected via UART5 on Pi4
|
||||
|
||||
[printer]
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
#max_accel_to_decel: 2000
|
||||
|
||||
################################################################################
|
||||
# Bed leveling
|
||||
################################################################################
|
||||
|
||||
[bed_screws]
|
||||
screw5: 127.5,105
|
||||
screw5_name: center virtual screw
|
||||
|
||||
################################################################################
|
||||
# Resonance compensation
|
||||
################################################################################
|
||||
|
||||
[input_shaper]
|
||||
|
||||
################################################################################
|
||||
@@ -58,8 +58,8 @@ uart_address: 1
|
||||
[tmc2209 extruder]
|
||||
uart_pin: TMC_UART_PIN
|
||||
tx_pin: TMC_TX_PIN
|
||||
run_current: 0.400
|
||||
hold_current: 0.200
|
||||
run_current: 0.600
|
||||
hold_current: 0.300
|
||||
stealthchop_threshold: 999999
|
||||
uart_address: 3
|
||||
|
||||
@@ -70,17 +70,20 @@ uart_address: 3
|
||||
|
||||
[gcode_macro HIGH_SPEED]
|
||||
gcode:
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT=1.000 HOLDCURRENT=0.750
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT=1.000 HOLDCURRENT=0.750
|
||||
SET_TMC_CURRENT STEPPER=extruder CURRENT=0.600 HOLDCURRENT=0.300
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT=1.200 HOLDCURRENT=0.750
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT=1.200 HOLDCURRENT=0.750
|
||||
SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.800 HOLDCURRENT=0.400
|
||||
SET_TMC_CURRENT STEPPER=extruder CURRENT=0.800 HOLDCURRENT=0.400
|
||||
|
||||
[gcode_macro NORMAL_SPEED]
|
||||
gcode:
|
||||
{% set tmc_x = printer.configfile.settings["tmc2209 stepper_x"] %}
|
||||
{% set tmc_y = printer.configfile.settings["tmc2209 stepper_y"] %}
|
||||
{% set tmc_z = printer.configfile.settings["tmc2209 stepper_z"] %}
|
||||
{% set tmc_e = printer.configfile.settings["tmc2209 extruder"] %}
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={tmc_x.run_current} HOLDCURRENT={tmc_x.hold_current}
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={tmc_y.run_current} HOLDCURRENT={tmc_y.hold_current}
|
||||
SET_TMC_CURRENT STEPPER=stepper_z CURRENT={tmc_z.run_current} HOLDCURRENT={tmc_z.hold_current}
|
||||
SET_TMC_CURRENT STEPPER=extruder CURRENT={tmc_e.run_current} HOLDCURRENT={tmc_e.hold_current}
|
||||
|
||||
################################################################################
|
||||
|
||||
Reference in New Issue
Block a user