Update fan pin assignments for BIGTREETECH-SKR-mini-E3.cfg and tmc2209_uart_mks_rn.cfg

Flying Bear Generic Configs/board/BIGTREETECH-SKR-mini-E3.cfg

@@ -29,8 +29,9 @@ aliases:
   E_HEATER_PIN=PC8, E_SENSOR_PIN=PA0, 
   BED_HEATER_PIN=PC9, BED_SENSOR_PIN=PC4, 
 ## Fans ########################################################################
-  HEATER_FAN_PIN=PB15,
+  HEATER_FAN_PIN=PC7,
-  PARTCOOLING_FAN_PIN=PC7, 
+  PARTCOOLING_FAN_PIN=PC6,
+  FUN2_FAN_PIN=PB15,  
 ## Controls ####################################################################
   EXP1_1=PB5,  EXP1_3=PA9,   EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
   EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9,  EXP1_8=PD6, EXP1_10=<5V>, 

Flying Bear Generic Configs/printer.cfg

@@ -0,0 +1,113 @@
+################################################################################
+# Board: MKS Robin Nano v1.1 (Flying Bear Reborn 2.0) / MKS Robin Nano v1.3 / MKS Robin Nano-S v1.3
+# Printer: Flying Bear Ghost 5
+# Config by ODUCCEU
+################################################################################
+
+# Documentation
+# https://www.klipper3d.org/Config_Reference.html
+
+# Rename this file to 'printer.cfg'.
+# Enable proper 'Control board' in 'Included configs' section.
+
+# It is recommended that you follow these steps to properly calibrate your printer:
+# 1) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
+# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
+# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
+# 4) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
+
+################################################################################
+# Included configs
+################################################################################
+
+# Duplicate parameters in included config files will override each other.
+# In this case, each next included file overwrites the previous one in the list.
+# 'printer.cfg' takes precedence over other included files.
+# Try to avoid changing the default files by adding or changing parameters in 'printer.cfg' below.
+# This does not apply to commented out parameters.
+
+## Control board ###############################################################
+# THERE CAN BE ONLY ONE!
+[include board/BIGTREETECH-SKR-mini-E3.cfg]                                                   # MKS Robin Nano v1.1 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-11.jpg
+# [include board/mks-rn-13.cfg]                                                   # MKS Robin Nano v1.3 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-13.png
+# [include board/mks-rn-s-13.cfg]                                                 # MKS Robin Nano-S v1.3 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-s-13.png
+# [include board/mks-rn-s-13-E-on-5.cfg]                                          # MKS Robin Nano-S v1.3 with extruder plugged to E1 https://github.com/oducceu/klipper_configs/blob/master/images/mks-rn-s-13-E-on-5.png
+
+## Base configuration ##########################################################
+[include printer/fb-ghost5.cfg]
+
+## Drivers #####################################################################
+# [include printer/tmc2225.cfg]
+[include printer/tmc2209_uart_mks_rn.cfg]                                       # enable if using TMC drivers via UART on MKS Robin Nano
+
+## Base macros #################################################################
+[include macros/macros.cfg]
+
+## Additional hardware #########################################################
+[include printer/fb-ghost5-bltouch.cfg]                                         # disable 'position_endstop' in [stepper_z] section
+# [include printer/rpi_mcu.cfg]                                                   # enable ONLY after setting Pi as MCU https://www.klipper3d.org/RPi_microcontroller.html
+# [include printer/accelerometer.cfg]                                             # requires "rpi.cfg"
+
+[include mainsail.cfg]
+
+################################################################################
+# X, Y, Z
+################################################################################
+
+[stepper_x]
+homing_speed: 150
+
+[stepper_y]
+homing_speed: 150
+
+[stepper_z]
+#position_endstop: 0.5                                                           # disable if using BLTouch to use 'probe:z_virtual_endstop'
+
+################################################################################
+# E0, HB
+################################################################################
+
+[extruder]
+rotation_distance: 7.600                                                        # CAUTION! Calibrate using https://www.klipper3d.org/Rotation_Distance.html
+nozzle_diameter: 0.400
+pressure_advance: 0.000                                                         # CAUTION! Calibrate using https://www.klipper3d.org/Pressure_Advance.html
+control: pid                                                                    # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands
+pid_Kp: 30.891
+pid_Ki: 2.542
+pid_Kd: 93.830
+# min_extrude_temp: 0                                                           # allow Cold Extrusion for extruder steps calibration
+
+[heater_bed]
+control: pid                                                                    # CAUTION! Calibrate using PID_CALIBRATE https://www.klipper3d.org/G-Codes.html#extended-g-code-commands
+pid_Kp: 63.104
+pid_Ki: 2.350
+pid_Kd: 423.586
+
+################################################################################
+# Printer
+################################################################################
+
+[mcu]
+# serial: /dev/ttyAMA0                                                          # enable if connected via UART1 on Pi3/PiZ
+# serial: /dev/ttyAMA1                                                          # enable if connected via UART5 on Pi4
+
+[printer]
+max_velocity: 300
+max_accel: 3000
+#max_accel_to_decel: 2000
+
+################################################################################
+# Bed leveling
+################################################################################
+
+[bed_screws]
+screw5: 127.5,105
+screw5_name: center virtual screw
+
+################################################################################
+# Resonance compensation
+################################################################################
+
+[input_shaper]
+
+################################################################################

Flying Bear Generic Configs/printer/tmc2209_uart_mks_rn.cfg

@@ -42,7 +42,7 @@ hold_current: 0.400
 sense_resistor: 0.110
 diag_pin: PC1
 driver_SGTHRS: 100
-stealthchop_threshold: 999999
+stealthchop_threshold: 999999   
 
 
 [tmc2209 stepper_z]
@@ -58,8 +58,8 @@ uart_address: 1
 [tmc2209 extruder]
 uart_pin: TMC_UART_PIN
 tx_pin: TMC_TX_PIN
-run_current: 0.400
+run_current: 0.600
-hold_current: 0.200
+hold_current: 0.300
 stealthchop_threshold: 999999
 uart_address: 3
 
@@ -70,17 +70,20 @@ uart_address: 3
 
 [gcode_macro HIGH_SPEED]
 gcode:
-    SET_TMC_CURRENT STEPPER=stepper_x CURRENT=1.000 HOLDCURRENT=0.750
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT=1.200 HOLDCURRENT=0.750
-    SET_TMC_CURRENT STEPPER=stepper_y CURRENT=1.000 HOLDCURRENT=0.750
+    SET_TMC_CURRENT STEPPER=stepper_y CURRENT=1.200 HOLDCURRENT=0.750
-    SET_TMC_CURRENT STEPPER=extruder CURRENT=0.600 HOLDCURRENT=0.300
+    SET_TMC_CURRENT STEPPER=stepper_z CURRENT=0.800 HOLDCURRENT=0.400
+    SET_TMC_CURRENT STEPPER=extruder CURRENT=0.800 HOLDCURRENT=0.400
     
 [gcode_macro NORMAL_SPEED]
 gcode:
     {% set tmc_x = printer.configfile.settings["tmc2209 stepper_x"] %}
     {% set tmc_y = printer.configfile.settings["tmc2209 stepper_y"] %}
+    {% set tmc_z = printer.configfile.settings["tmc2209 stepper_z"] %}
     {% set tmc_e = printer.configfile.settings["tmc2209 extruder"] %}
     SET_TMC_CURRENT STEPPER=stepper_x CURRENT={tmc_x.run_current} HOLDCURRENT={tmc_x.hold_current}
     SET_TMC_CURRENT STEPPER=stepper_y CURRENT={tmc_y.run_current} HOLDCURRENT={tmc_y.hold_current}
+    SET_TMC_CURRENT STEPPER=stepper_z CURRENT={tmc_z.run_current} HOLDCURRENT={tmc_z.hold_current}
     SET_TMC_CURRENT STEPPER=extruder CURRENT={tmc_e.run_current} HOLDCURRENT={tmc_e.hold_current}
 
 ################################################################################