New backup from 05/06/24 - 17:06:35

steel_data/config/printer.cfg

@@ -0,0 +1,163 @@
+[include shell_command.cfg]
+[include fluidd.cfg]
+
+[virtual_sdcard]
+path: /home/jeka/steel_data/gcodes
+on_error_gcode: CANCEL_PRINT
+
+[include macros.cfg]
+
+[virtual_sdcard]
+path: /home/jeka/steel_data/gcodes
+on_error_gcode: CANCEL_PRINT
+ 
+[mcu]
+serial: /dev/ttySteel
+ 
+# ================================================================================
+# Homing Override:  
+# This section is called any time a G28 [home] is called.  
+ 
+;[homing_override]
+;set_position_z:0
+;gcode:
+;    G1 Z10 F600
+;    G28 X Y
+;    G1 X102.5 Y99.5 F6000
+;    G28 Z
+;    G1 Z5
+ 
+#[bed_mesh]
+#speed: 80
+#horizontal_move_z: 5
+#mesh_min: 15,15
+#mesh_max: 180,180
+#probe_count: 3, 3
+#mesh_pps: 2, 2
+#fade_start: 1
+#fade_end: 10
+#fade_target: 0
+
+[bed_screws]
+screw1: 15,10
+screw2: 15,185
+screw3: 185,10
+screw4: 185,185
+
+#[safe_z_home]
+#home_xy_position = 0,0
+#speed = 50
+#z_hop = 5
+#_hop_speed = 5
+
+[stepper_x]
+step_pin: PF0
+dir_pin: !PF1
+enable_pin: !PD7
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^!PE4
+position_endstop: 200
+position_max: 200
+position_min: 0
+homing_speed: 50
+ 
+[stepper_y]
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^!PJ0
+position_endstop: 200
+position_max: 200
+position_min: 0
+homing_speed: 50
+ 
+[stepper_z]
+step_pin: PL3
+dir_pin: !PL1
+enable_pin: !PK0
+microsteps: 16
+rotation_distance: 0.8
+endstop_pin: ^!PD3
+#position_endstop: 0.0
+position_max: 270
+position_min: -5
+homing_speed: 20
+ 
+[extruder]
+max_extrude_only_distance: 101.0
+step_pin: PA4
+dir_pin: PA6
+enable_pin: !PA2
+microsteps: 16
+rotation_distance: 22.222
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5
+#control: pid
+min_temp: 0
+max_temp: 250
+#pid_kp = 21.801
+#pid_ki = 1.546
+#pid_kd = 76.848
+ 
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: watermark
+min_temp: 0
+max_temp: 110
+;pid_kp = 72.814
+;pid_ki = 1.634
+;pid_kd = 810.970
+ 
+[fan]
+pin: PH6
+ 
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+square_corner_velocity: 20.0
+ 
+[display]
+lcd_type: st7920
+cs_pin: EXP1_4
+sclk_pin: EXP1_5
+sid_pin: EXP1_3
+encoder_pins: ^EXP2_3, ^EXP2_5
+click_pin: ^!EXP1_2
+ 
+;[output_pin BEEPER_pin]
+;ipin: EXP1_1
+ 
+# Common EXP1 / EXP2 (display) pins
+[board_pins]
+aliases:
+    # Common EXP1 header found on many "all-in-one" ramps clones
+    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
+    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
+    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
+    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
+    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 28.696
+#*# pid_ki = 2.035
+#*# pid_kd = 101.153
+#*#
+#*# [stepper_z]
+#*# position_endstop = 0.030