mirror of
https://github.com/Laxilef/OTGateway.git
synced 2025-12-10 18:24:27 +05:00
396 lines
12 KiB
JSON
396 lines
12 KiB
JSON
{
|
|
"values": {
|
|
"logo": "OpenTherm Gateway",
|
|
"nav": {
|
|
"license": "License",
|
|
"source": "Source code",
|
|
"help": "Help",
|
|
"issues": "Issues & questions",
|
|
"releases": "Releases"
|
|
},
|
|
"dbm": "dBm",
|
|
"kw": "kW",
|
|
"time": {
|
|
"days": "d.",
|
|
"hours": "h.",
|
|
"min": "min.",
|
|
"sec": "sec."
|
|
},
|
|
|
|
"button": {
|
|
"upgrade": "Upgrade",
|
|
"restart": "Restart",
|
|
"save": "Save",
|
|
"saved": "Saved",
|
|
"refresh": "Refresh",
|
|
"restore": "Restore",
|
|
"restored": "Restored",
|
|
"backup": "Backup",
|
|
"wait": "Please wait...",
|
|
"uploading": "Uploading...",
|
|
"success": "Success",
|
|
"error": "Error"
|
|
},
|
|
|
|
"index": {
|
|
"title": "OpenTherm Gateway",
|
|
|
|
"section": {
|
|
"network": "Network",
|
|
"system": "System"
|
|
},
|
|
|
|
"system": {
|
|
"build": {
|
|
"title": "Build",
|
|
"version": "Version",
|
|
"date": "Date",
|
|
"core": "Core",
|
|
"sdk": "SDK"
|
|
},
|
|
"uptime": "Uptime",
|
|
"memory": {
|
|
"title": "Free memory",
|
|
"maxFreeBlock": "max free block",
|
|
"min": "min"
|
|
},
|
|
"board": "Board",
|
|
"chip": {
|
|
"model": "Chip",
|
|
"cores": "Cores",
|
|
"freq": "frequency"
|
|
},
|
|
"flash": {
|
|
"size": "Flash size",
|
|
"realSize": "real size"
|
|
},
|
|
"lastResetReason": "Last reset reason"
|
|
}
|
|
},
|
|
|
|
"dashboard": {
|
|
"name": "Dashboard",
|
|
"title": "Dashboard - OpenTherm Gateway",
|
|
|
|
"section": {
|
|
"control": "Control",
|
|
"states": "States and sensors",
|
|
"otDiag": "OpenTherm diagnostic"
|
|
},
|
|
|
|
"thermostat": {
|
|
"heating": "Heating",
|
|
"dhw": "DHW",
|
|
"temp.current": "Current",
|
|
"enable": "Enable",
|
|
"turbo": "Turbo mode"
|
|
},
|
|
|
|
"state": {
|
|
"ot": "OpenTherm connected",
|
|
"mqtt": "MQTT connected",
|
|
"emergency": "Emergency",
|
|
"heating": "Heating",
|
|
"dhw": "DHW",
|
|
"flame": "Flame",
|
|
"fault": "Fault",
|
|
"diag": "Diagnostic",
|
|
"extpump": "External pump",
|
|
"outdoorSensorConnected": "Outdoor sensor connected",
|
|
"outdoorSensorRssi": "Outdoor sensor RSSI",
|
|
"outdoorSensorHumidity": "Outdoor sensor humidity",
|
|
"outdoorSensorBattery": "Outdoor sensor battery",
|
|
"indoorSensorConnected": "Indoor sensor connected",
|
|
"cascadeControlInput": "Cascade control (input)",
|
|
"cascadeControlOutput": "Cascade control (output)",
|
|
"indoorSensorRssi": "Indoor sensor RSSI",
|
|
"indoorSensorHumidity": "Indoor sensor humidity",
|
|
"indoorSensorBattery": "Indoor sensor battery",
|
|
"modulation": "Modulation",
|
|
"pressure": "Pressure",
|
|
"dhwFlowRate": "DHW flow rate",
|
|
"power": "Current power",
|
|
"faultCode": "Fault code",
|
|
"diagCode": "Diagnostic code",
|
|
"indoorTemp": "Indoor temp",
|
|
"outdoorTemp": "Outdoor temp",
|
|
"heatingTemp": "Heating temp",
|
|
"heatingSetpointTemp": "Heating setpoint temp",
|
|
"heatingReturnTemp": "Heating return temp",
|
|
"dhwTemp": "DHW temp",
|
|
"exhaustTemp": "Exhaust temp"
|
|
}
|
|
},
|
|
|
|
"network": {
|
|
"title": "Network - OpenTherm Gateway",
|
|
"name": "Network settings",
|
|
|
|
"section": {
|
|
"static": "Static settings",
|
|
"availableNetworks": "Available networks",
|
|
"staSettings": "WiFi settings",
|
|
"apSettings": "AP settings"
|
|
},
|
|
|
|
"scan": {
|
|
"pos": "#",
|
|
"info": "Info"
|
|
},
|
|
|
|
"wifi": {
|
|
"ssid": "SSID",
|
|
"password": "Password",
|
|
"channel": "Channel",
|
|
"signal": "Signal",
|
|
"connected": "Connected"
|
|
},
|
|
|
|
"params": {
|
|
"hostname": "Hostname",
|
|
"dhcp": "Use DHCP",
|
|
"mac": "MAC",
|
|
"ip": "IP",
|
|
"subnet": "Subnet",
|
|
"gateway": "Gateway",
|
|
"dns": "DNS"
|
|
},
|
|
|
|
"sta": {
|
|
"channel.note": "set 0 for auto select"
|
|
}
|
|
},
|
|
|
|
"settings": {
|
|
"title": "Settings - OpenTherm Gateway",
|
|
"name": "Settings",
|
|
|
|
"section": {
|
|
"portal": "Portal settings",
|
|
"system": "System settings",
|
|
"diag": "Diagnostic",
|
|
"heating": "Heating settings",
|
|
"dhw": "DHW settings",
|
|
"emergency": "Emergency mode settings",
|
|
"equitherm": "Equitherm settings",
|
|
"pid": "PID settings",
|
|
"ot": "OpenTherm settings",
|
|
"mqtt": "MQTT settings",
|
|
"outdorSensor": "Outdoor sensor settings",
|
|
"indoorSensor": "Indoor sensor settings",
|
|
"extPump": "External pump settings",
|
|
"cascadeControl": "Cascade control settings"
|
|
},
|
|
|
|
"enable": "Enable",
|
|
"note": {
|
|
"restart": "After changing these settings, the device must be restarted for the changes to take effect.",
|
|
"blankNotUse": "blank - not use",
|
|
"bleDevice": "BLE device can be used <u>only</u> with some ESP32 boards with BLE support!"
|
|
},
|
|
|
|
"temp": {
|
|
"min": "Minimum temperature",
|
|
"max": "Maximum temperature"
|
|
},
|
|
|
|
"portal": {
|
|
"login": "Login",
|
|
"password": "Password",
|
|
"auth": "Require authentication"
|
|
},
|
|
|
|
"system": {
|
|
"unit": "Unit system",
|
|
"metric": "Metric <small>(celsius, liters, bar)</small>",
|
|
"imperial": "Imperial <small>(fahrenheit, gallons, psi)</small>",
|
|
"statusLedGpio": "Status LED GPIO",
|
|
"logLevel": "Log level",
|
|
"serial": {
|
|
"enable": "Enable Serial port",
|
|
"baud": "Serial port baud rate"
|
|
},
|
|
"telnet": {
|
|
"enable": "Enable Telnet",
|
|
"port": {
|
|
"title": "Telnet port",
|
|
"note": "Default: 23"
|
|
}
|
|
}
|
|
},
|
|
|
|
"heating": {
|
|
"hyst": "Hysteresis <small>(in degrees)</small>"
|
|
},
|
|
|
|
"emergency": {
|
|
"desc": "<b>!</b> Emergency mode can be useful <u>only</u> when using Equitherm and/or PID (when normal work) and when reporting indoor/outdoor temperature via MQTT/API/BLE. In this mode, sensor values that are reported via MQTT/API/BLE are not used.",
|
|
|
|
"target": {
|
|
"title": "Target temperature",
|
|
"note": "<u>Indoor temperature</u> if Equitherm or PID is <b>enabled</b><br /><u>Heat carrier temperature</u> if Equitherm and PID <b>is disabled</b>"
|
|
},
|
|
"treshold": "Treshold time <small>(sec)</small>",
|
|
|
|
"events": {
|
|
"desc": "Events",
|
|
"network": "On network fault",
|
|
"mqtt": "On MQTT fault",
|
|
"indoorSensorDisconnect": "On loss connection with indoor sensor",
|
|
"outdoorSensorDisconnect": "On loss connection with outdoor sensor"
|
|
},
|
|
|
|
"regulators": {
|
|
"desc": "Using regulators",
|
|
"equitherm": "Equitherm <small>(requires at least an external (DS18B20) or boiler <u>outdoor</u> sensor)</small>",
|
|
"pid": "PID <small>(requires at least an external (DS18B20) <u>indoor</u> sensor)</small>"
|
|
}
|
|
},
|
|
|
|
"equitherm": {
|
|
"n": "N factor",
|
|
"k": "K factor",
|
|
"t": {
|
|
"title": "T factor",
|
|
"note": "Not used if PID is enabled"
|
|
}
|
|
},
|
|
|
|
"pid": {
|
|
"p": "P factor",
|
|
"i": "I factor",
|
|
"d": "D factor",
|
|
"dt": "DT <small>in seconds</small>"
|
|
},
|
|
|
|
"ot": {
|
|
"advanced": "Advanced Settings",
|
|
"inGpio": "In GPIO",
|
|
"outGpio": "Out GPIO",
|
|
"ledGpio": "RX LED GPIO",
|
|
"memberIdCode": "Master MemberID code",
|
|
"maxMod": "Max modulation level",
|
|
"pressureFactor": {
|
|
"title": "Coeff. pressure correction",
|
|
"note": "If the pressure displayed is <b>X10</b> from the real one, set the <b>0.1</b>."
|
|
},
|
|
"dhwFlowRateFactor": {
|
|
"title": "Coeff. DHW flow rate correction",
|
|
"note": "If the DHW flow rate displayed is <b>X10</b> from the real one, set the <b>0.1</b>."
|
|
},
|
|
"minPower": {
|
|
"title": "Min boiler power <small>(kW)</small>",
|
|
"note": "This value is at 0-1% boiler modulation level. Typically found in the boiler specification as \"minimum useful heat output\"."
|
|
},
|
|
"maxPower": {
|
|
"title": "Max boiler power <small>(kW)</small>",
|
|
"note": "<b>0</b> - try detect automatically. Typically found in the boiler specification as \"maximum useful heat output\"."
|
|
},
|
|
"fnv": {
|
|
"desc": "Filtering numeric values",
|
|
"enable": {
|
|
"title": "Enable filtering",
|
|
"note": "It can be useful if there is a lot of sharp noise on the charts. The filter used is \"Running Average\"."
|
|
},
|
|
"factor": {
|
|
"title": "Filtration coeff.",
|
|
"note": "The lower the value, the smoother and <u>longer</u> the change in numeric values."
|
|
}
|
|
},
|
|
|
|
"options": {
|
|
"desc": "Options",
|
|
"dhwPresent": "DHW present",
|
|
"summerWinterMode": "Summer/winter mode",
|
|
"heatingCh2Enabled": "Heating CH2 always enabled",
|
|
"heatingCh1ToCh2": "Duplicate heating CH1 to CH2",
|
|
"dhwToCh2": "Duplicate DHW to CH2",
|
|
"dhwBlocking": "DHW blocking",
|
|
"modulationSyncWithHeating": "Sync modulation with heating",
|
|
"getMinMaxTemp": "Get min/max temp from boiler",
|
|
"immergasFix": "Fix for Immergas boilers"
|
|
},
|
|
|
|
"nativeHeating": {
|
|
"title": "Native heating control (boiler)",
|
|
"note": "Works <u>ONLY</u> if the boiler requires the desired room temperature and regulates the temperature of the coolant itself. Not compatible with PID and Equitherm regulators and hysteresis in firmware."
|
|
}
|
|
},
|
|
|
|
"mqtt": {
|
|
"homeAssistantDiscovery": "Home Assistant Discovery",
|
|
"server": "Server",
|
|
"port": "Port",
|
|
"user": "User",
|
|
"password": "Password",
|
|
"prefix": "Prefix",
|
|
"interval": "Publish interval <small>(sec)</small>"
|
|
},
|
|
|
|
"tempSensor": {
|
|
"source": {
|
|
"type": "Source type",
|
|
"boiler": "From boiler via OpenTherm",
|
|
"manual": "Manual via MQTT/API",
|
|
"ext": "External (DS18B20)",
|
|
"ble": "BLE device"
|
|
},
|
|
"gpio": "GPIO",
|
|
"offset": "Temp offset <small>(calibration)</small>",
|
|
"bleAddress": "BLE device MAC address"
|
|
},
|
|
|
|
"extPump": {
|
|
"use": "Use external pump",
|
|
"gpio": "Relay GPIO",
|
|
"postCirculationTime": "Post circulation time <small>(min)</small>",
|
|
"antiStuckInterval": "Anti stuck interval <small>(days)</small>",
|
|
"antiStuckTime": "Anti stuck time <small>(min)</small>"
|
|
},
|
|
|
|
"cascadeControl": {
|
|
"input": {
|
|
"desc": "Can be used to turn on the heating only if another boiler is faulty. The other boiler controller must change the state of the GPIO input in the event of a fault.",
|
|
"enable": "Enable input",
|
|
"gpio": "GPIO",
|
|
"invertState": "Invert GPIO state",
|
|
"thresholdTime": "State change threshold time <small>(sec)</small>"
|
|
},
|
|
"output": {
|
|
"desc": "Can be used to switch on another boiler <u>via relay</u>.",
|
|
"enable": "Enable output",
|
|
"gpio": "GPIO",
|
|
"invertState": "Invert GPIO state",
|
|
"thresholdTime": "State change threshold time <small>(sec)</small>",
|
|
"events": {
|
|
"desc": "Events",
|
|
"onFault": "If the fault state is active",
|
|
"onLossConnection": "If the connection via Opentherm is lost",
|
|
"onEnabledHeating": "If heating is enabled"
|
|
}
|
|
}
|
|
}
|
|
},
|
|
|
|
"upgrade": {
|
|
"title": "Upgrade - OpenTherm Gateway",
|
|
"name": "Upgrade",
|
|
|
|
"section": {
|
|
"backupAndRestore": "Backup & restore",
|
|
"backupAndRestore.desc": "In this section you can save and restore a backup of ALL settings.",
|
|
"upgrade": "Upgrade",
|
|
"upgrade.desc": "In this section you can upgrade the firmware and filesystem of your device.<br />Latest releases can be downloaded from the <a href=\"https://github.com/Laxilef/OTGateway/releases\" target=\"_blank\">Releases page</a> of the project repository."
|
|
},
|
|
|
|
"note": {
|
|
"disclaimer1": "After a successful upgrade the filesystem, ALL settings will be reset to default values! Save backup before upgrading.",
|
|
"disclaimer2": "After a successful upgrade, the device will automatically reboot after 10 seconds."
|
|
},
|
|
|
|
"settingsFile": "Settings file",
|
|
"fw": "Firmware",
|
|
"fs": "Filesystem"
|
|
}
|
|
}
|
|
} |