[include shell_command.cfg]
[include fluidd.cfg]

[virtual_sdcard]
path: /home/jeka/3dsprinter_data/gcodes
on_error_gcode: CANCEL_PRINT

[include macros.cfg]

[mcu]
serial: /dev/serial/by-id/usb-Arduino__www.arduino.cc__0042_75638303037351301112-if00

[bed_screws]
screw1: 15,5
screw1_name: Front left screw
screw2: 15,180
screw2_name: Rear left screw 
screw3: 285,5
screw3_name: Front right screw 
screw4: 285,180
screw4_name: Rear right screw

[screws_tilt_adjust]
horizontal_move_z: 5
screw1: 8,181
screw1_name: back left
screw2: 298,181
screw2_name: back right
screw3: 8,21
screw3_name: front left
screw4: 298,21
screw4_name: front right
screw_thread: CW-M3

[bltouch]
sensor_pin: PD3 #^PD3
control_pin: PB5
x_offset: 0
y_offset: -20
speed: 10.0
samples: 2
speed: 2
#z_offset: 0.0
pin_up_reports_not_triggered: True
pin_up_touch_mode_reports_triggered: False
#pin_up_touch_mode_reports_triggered: True


[safe_z_home]
home_xy_position: 145, 95# Change coordinates to the center of your print bed
speed: 50
z_hop: 10 # Move up 10mm
z_hop_speed: 5

[bed_mesh]
speed: 60
horizontal_move_z: 5
mesh_min: 20,20
mesh_max: 285,150
probe_count: 5,3
mesh_pps: 2,2
fade_start: 1
fade_end: 10
fade_target: 0

[stepper_x]
step_pin: PF0
dir_pin: !PF1
enable_pin: !PD7
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PE5
position_endstop: 0
position_max: 305
homing_speed: 50

[stepper_y]
step_pin: PF6
dir_pin: !PF7
enable_pin: !PF2
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PJ0
position_endstop: 189
position_max: 189
homing_speed: 50

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
microsteps: 16
rotation_distance: 8
endstop_pin: ^!PD2
endstop_pin: probe:z_virtual_endstop 
#homing_positive_dir: true
#position_endstop: 278
position_max: 270
position_min: -6
homing_speed = 15

[extruder]
max_extrude_only_distance: 101.0
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
microsteps: 16
rotation_distance: 7.920
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
#control: pid
#pid_Kp: 22.2
#pid_Ki: 1.08
#pid_Kd: 114
min_temp: 0
max_temp: 250

[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: watermark
min_temp: 0
max_temp: 130

[fan]
pin: PH6

[printer]
kinematics: corexy
max_velocity: 500
max_accel: 5000
max_z_accel: 30
max_z_velocity: 30

[display]
lcd_type: hd44780
rs_pin: EXP1_4
e_pin: EXP1_3
d4_pin: EXP1_5
d5_pin: EXP1_6
d6_pin: EXP1_7
d7_pin: EXP1_8
encoder_pins: ^EXP2_3, ^EXP2_5
click_pin: ^!EXP1_2


[board_pins]
aliases:
    # Common EXP1 header found on many "all-in-one" ramps clones
    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
    # EXP2 header
    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 25.328
#*# pid_ki = 1.578
#*# pid_kd = 101.628
#*#
#*# [heater_bed]
#*# pid_kp = 72.255
#*# pid_ki = 1.487
#*# pid_kd = 877.904
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.037500, -0.042500, -0.027500, -0.016250, 0.016250
#*# 	  -0.017500, -0.006250, 0.042500, 0.056250, 0.036250
#*# 	  0.045000, 0.062500, 0.098750, 0.116250, 0.076250
#*# x_count = 5
#*# y_count = 3
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = lagrange
#*# tension = 0.2
#*# min_x = 20.0
#*# max_x = 285.0
#*# min_y = 20.0
#*# max_y = 150.0
#*#
#*# [bltouch]
#*# z_offset = 2.290